Daftar Kode Error Mesin Fotocopy Canon Seri Image Runner [General]

Author:
Daftar Kode Error Mesin Fotocopy Canon Seri Image Runner [General]: Berikut adalah daftar kode error mesin fotocopy merk Canon dengan seri iR (Image Runner) Semua type secara umum. Sobat teknisi atau operator mesin fotocopy dapat memanfaatkan daftar kode error berikut untuk mendeteksi kerusakan yang timbul pada mesin fotocopy merk Canon dengan seri Image Runner.

E code Description Category Remarks
E000 The fixing temperature does not go up after turning ON the power due to a fault in the thermistor or the heater, etc.,
e.g.) It does not reach 70 C degrees within 2 min.
Related fxixng unit  
E001 The fixing temperature abnormally goes up due to a fault in the thermistor or SSR, etc.  
E002 The fixing temperature does not reach a specific temperature due to a fault in the thermistor or the heater, etc.
e.g) The fixing temperature does not go up to 190 C degrees within 5 min after reaching 70 C degrees.
 
E003 The fixing temperature drops abnormally after wait time is up due to a fault in the thermistor, the heater, etc.
e.g.) After wait time is up, the fixing temperature drops to 70 C degrees.
 
E004 A short circuit in the fixing heater drive circuit (SSR, etc) is detected.  
E005 The fixing web is wound up completely.  
E006 The fixing drawer connector is not connected as the front door is closed.  
E007 The fixing film is off to the side.  
E008 A specific number of copies are made after the machine detects that fixing oil is out. Since a user cannot re-supply fixing oil, the error code is indicated.
E009 The rated voltage of the power supply and that of the fixing unit do not match.  
E010 Clock pulses fail to be generated or the PLL lock fails to be released due to a fault in the main motor, etc. Related drum drive unit and main drive unit  
E011 Excess current flows to the motor control circuit because the main motor is locked up, etc.  
E012 Clock pulses fail to be generated or the PLL lock is released due to a fault in the drum motor, etc. In case the drum drive motor exists in addition to the main motor, this code refers to an error of a motor which drives mainly other units than the drum.
E013 •The PLL lock is released because waste toner motor is locked up, etc.
•The micro switch employed to detect clogging of waste toner is activated.
•The waste toner case is detected full.
 
E014 •The PLL lock of the fixing/feeding motor is released.
•Excess current of the feeding motor is detected.
 
E015 •Clock pulses of the pick-up/duplexing/developing motor fails to be generated or be detected.
•Excess current of the pick-up/duplexing/developing motor is detected.
 
E016 Excess current of the reciprocating motor of the photosensitive drum cleaner unit is detected.  
E017 The PLL lock of the drive motor of the holding tray unit is released.  
E018 The PLL lock of the drive motor of the oil removing roller is released.  
E019 The waste toner case is detected full although it is not.  
E020 The developer fails to be replenished with starter developer properly. Related developing unit A hopper motor error is identified by the detail code of E020. However, it may be identified by E02x according to need.
E021 The rotor fails to rotate and move properly due to a fault in the developing rotor/motor ass'y.  
E022 Pressure fails to be applied to the developer after a specific time passes after the developer is selected.  
E023 The developer sleeve motor fails to rotate properly.  
E024 The developer cannot be detected. (The developer is not mounted properly.)  
E025 Excess current of the toner delivery motor or the cartridge motor is detected.  
E026    
E027    
E028    
E029    
E030 The total counters are not functioning. Related counter  
E031 The optional counters are not functioning.  
E032 The counters for ASSIST are not functioning. (Disconnection of counter pulse for ASSIST.)  
E033    
E034    
E035    
E036    
E037    
E038    
E039    
E040 The lifter position signal fails to be generated due to a lifter clutch failure. Related paper pick-up unit  
E041 The paper deck lifter fails to be detected within a specific time.  
E042 The roll paper cutting operation is not functioning properly because the cut motor does not work, etc.  
E043 An abnormal signal is detected due to a fault in the pick-up motor for the 3-cassette deck/3.5K paper deck.  
E044    
E045    
E046    
E047    
E048    
E049    
E050 A malfunction of the holding tray. A fault in the side registration is included. Related duplex unit The duplexing unit for the stack system
E051 The home position of the side registration cannot be detected within a specific time. The duplexing unit for the through-path system
E052    
E053    
E054 The home position of the duplexing unit feed roller cannot be detected.  
E055 The horizontal registration guide of the duplex unit exceeds its maximum travel distance.  
E056    
E057    
E058    
E059    
E060 The home position of the primary corona wire cleaner cannot be detected within a specific time. Relateted charging  
E061 Specific potential is not be required or the limiter is activated as the potential is controlled.  
E062 The photosensitive drum temperature does not reach a specific value due to a fault in the photosensitive drum heater, etc.  
E063 The home position of the transfer corona wire cleaner cannot be detected. An error code is not to be indicated.
E064 The setting value for the output from the microcomputer considerably deviates from the control value of the actual output.  
E065 High voltage leakage from the primary corona assembly is detected.  
E066 Signals from the temperature/humidity sensor cannot be detected.  
E067 Two or more faults in the primary/ pre (post)-transfer/ transfer/ separation high voltage are detected (including power output stoppage, electric leakage from the primary corona assembly).  
E068 High voltage leakage from or an open circuit in the separation corona assembly is detected.  
E069 High voltage leakage from or an open circuit in the transfer corona assembly is detected.  
E070 The home position of the transfer drum cannot be detected within a specific time. Related transfer  
E071 An image leading edge signal cannot be detected within a specific time.  
E072 A fault in the main motors such as the transfer drum motor, etc.  
E073 The transfer drawer connector or the transfer frame drawer connector is not connected as the front door is closed.  
E074 The transfer belt unit does not reach the target position within a specific time.  
E075 The transfer belt is off to the side.  
E076 The transfer belt web is wound up completely.  
E077 The motor inside the transfer belt unit has a fault.  
E078    
E079 The home position (to apply pressure) of the transfer drum cleaner unit cannot be detected.  
E080 An error occurs in the communication with the multi color unit controller PCB. Related developing unit for multi color unit  
E081 The vertical motor clock is faulty.  
E082 The horizontal motor clock is faulty.  
E083 The CD unit horizontal movement right sensor is faulty.  
E084 The CD unit horizontal movement left sensor is faulty.  
E085 The CD unit feeder release sensor is faulty.  
E086 The CD unit claw release is faulty.  
E087    
E088    
E089 A malfunction of the multi color unit.  
E090 The document feed motor is not functioning properly. related document feeder (bulit-into machine)  
E091 A failure in the detection of the document feed sensor.  
E092    
E093    
E094    
E095    
E096    
E097    
E098    
E099    
E100 The BD signal cannot be detected within a specific time. Related laser  
E101 The AF motor of the laser unit is faulty.  
E102 The light intensity of the laser does not reach a specific level.  
E103    
E104    
E105    
E106    
E107    
E108    
E109    
E110 The polygonal scanner motor does not reach a specific speed within a specific time. Related laser scnner  
E111 The polygonal cooling fan does not rotate properly.  
E112    
E113    
E114    
E115    
E116    
E117    
E118    
E119    
E120 The temperature of the laser does not reach a specific value. Related laser temperature control  
E121 The stoppage of the laser cooling fan is detected.  
E122    
E123    
E124    
E125    
E126    
E127    
E128    
E129    
E140 The movable guide motor is turned ON, and a specific position cannot be detected within a specific time. Related BJ  
E141 1. The capping motor is turned ON, and a specific position cannot be detected within a specific time.
2. A specific position of the cam sensor for the recovery system cannot be detected within a specific time.
 
E142 The pressure position switching motor is turned ON, and a specific position cannot be detected within a specific time.  
E143 The intake switching motor is turned ON, and a specific position cannot be detected within a specific time.  
E144 A detection signal is not returned to the ink pump monitor after the ink pump is activated: DCC -> BHD -> pump drive signal  
E145 No signal is generated from the position sensor within a specific time after a drive signal of the cutter motor is generated.  
E146 1. The waste ink full sensor is turned ON.
2. The intake counter for waste ink exceeds a specific value.
 
E147    
E148    
E149    
E150 Neither thermistor nor trimmer resistance is connected to the head. (The head is not connected.) Related BJ head  
E151 The thermistor of the head is open-circuited.  
E152 The thermistor of the head is short-circuited.  
E153 The trimmer resistance of the head is open-circuited.  
E154 The trimmer resistance of the head is short-circuited.  
E155 The trimmer resistance of the head is out of specifications.  
E156 When a specific voltage is applied to the head, the voltage of the head is not changed within a specific time.  
E157 The voltage of the head is out of the specifications.  
E158    
E159    
E160 The temperature of the head does not reach a specific temperature within a specific time. Related BJ head temperature control  
E161 The temperature of the head exceeds a specific temperature.  
E162    
E163    
E164    
E165    
E166    
E167    
E168    
E169    
E170 When the pulse motor for the head scan is driven, it cannot be detected by a sensor within a specific time. Related BJ head scanner  
E171 The motor is not connected to the pulse motor driver PCB for the head scan.  
E172 The gate array employed to drive the pulse motor for head scan is faulty.  
E173    
E174    
E175    
E176    
E177    
E178    
E179    
E180 The motor is not connected to the vertical scanning pulse motor driver PCB. Related BJ paper feed  
E181 The gate array employed to drive the vertical scanning pulse motor is faulty.  
E182 After the vertical scanning motor is driven, the phase sensor cannot be detected within a specific time.  
E183 After the registration roller cam clutch 2 is turned ON, a given paper size cannot be detected within a specific time.  
E184    
E185    
E186    
E187    
E188    
E189    
E190 RAM directly connected to CPU is faulty. Related CPU (printer unit) Failures in RAM of the laser controller are indicated with detail codes.
E191 An error occurs in the communication with the microcomputer (D/A converter) for high voltage use. Machines which do not have detail code function may use this code.
E192 An error occurs in the communication with A/D converter.  
E193 The gate array is faulty.  
E194 The auto registration is faulty.
Data from the # pattern reading CCD is invalid. 
 
E195 ROM failure -> No. of times data is written on EEPROM reaches the upper limit.  
E196 EEPROM failure: EEPROM read and write error (except software counter), an error in EEPROM areas on DIMM.  
E197 An error occurs in the communication within the printer:
•Errors continuously occur in the communication within the printer.
•Interruption during receiving is not made within a specific time.
 
E198 An error occurs in IC on the DC controller.  
E199    
E200 When the scanner moves forward, the scanner reversal sensor is activated. Related scanner (mainry, exposure ass'y, control panel)  
E201 The scanner is locked up, and excess current flows to the motor control circuit.  
E202 The scanner does not return to the home position for vertical scanning within a specific time. This code must not be indicated on the control panel. It should be checked with Service Mode.
E203 Clock pulses are not generated or the PLL lock is released due to a fault in the scanner motor, etc.  
E204 When the scanner moves forward, the document leading edge signal is not generated.  
E205 The scanning operation does not complete within a specific time.  
E206 The scanner does not return to the home position for horizontal scanning within a specific time.  
E207 After switching the wire tension of the scanner, sensor input is not made within a specific time.  
E208 (On machines which move the lens and the mirrors separately when setting a copy ratio)
Mirror 4 and 5 do not return to the HP sensor within a specific time.
 
E209 The scanner does not return to the CFF home position within a specific time. This code must not be indicated on control panel. It should be checked with Service Mode.
E210 The lens does not return to the home position within a specific time. (In the direction of light axis) Related lens  
E211 The thermistor of the scanner lamp is disconnected.  
E212 The lens does not return to the home position within a specific time. (In the direction of drum shaft)  
E213 When performing slide reading, the scanner comes off from the home position for slide reading.  
E214 Rotation of the scanner fan cannot be detected after a specific time passes.  
E215 The thermistor of the scanning lamp (fluorescent lamp) exceeds a specific temperature.  
E216 The scanner lamp (fluorescent lamp fails to turn ON after a specific time passes.  
E217 The temperature of the scanning lamp (fluorescent lamp) does not reach a specific temperature while the scanning lamp temperature is controlled.  
E218 •The scanner lamp (fluorescent lamp is turned ON while it is not properly set.
•The filament of the fluorescent lamp is blown out.
 
E219 The thermistor for the heater exceeds a specific temperature while the scanner lamp (fluorescent lamp is turned ON.  
E220 1. The scanning lamp is turned ON during stand-by.
2. The scanning lamp is turned OFF during copy operation.
Related exposure  
E221 The lamp regulator is faulty due to fluctuation of zero-cross signal.  
E222 The scanning lamp pre-heater is faulty.  
E223 1. The red filter does not return to the HP sensor within a specific time.
2. The red filter stays at the HP sensor after a specific time has passed.
Applied to all color filters
E224 The blank shutter does not return to the HP sensor within a specific time.  
E225 Insufficient light intensity of the scanning lamp: A specific level cannot be attained for the signal during CCD gain correction.  
E226 A malfunction of the scanner cooling fan is detected.  
E227    
E228    
E229    
E230 The horizontal scanning motor driver PCB is not connected to the CPU PCB. Related scanner drive unit  
E231 The vertical scanning motor driver PCB is not connected to the CPU PCB.  
E232    
E233    
E234    
E235    
E236    
E237    
E238    
E239    
E240 An error occurs in the communication between the master and the sleeve 0: Detail code is indicated. Related scanner CPU communication  
E241 An error occurs in the communication between the master and the sleeve 1. Machines which does not have the detail code function may use this code.
E242 An error occurs in the communication between the master and the sleeve 2. Machines which does not have the detail code function may use this code.
E243 An error occurs in the communication with control panel. Machines which does not have the detail code function may use this code.
E244 An error occurs in the communication between PCBs: CPUs exist on two or more PCBs, so the master and the sleeve are not be separable. Machines which does not have the detail code function may use this code.
E245 No. of times data is written on the soft counter memory reaches the upper limit.  
E246 Reading from/ writing to the soft counter memory cannot be done properly. An error occurs when checking DIMM: CP2120 (EEPROM areas on DIMM)
E247 The software counter memory PCB and the software counter value stored in SRAM are found inconsistent.  
E248 The EEPROM on the reader controller is faulty.
•Inconsistency between the read data and the write data.
•Inconsistency between the ID in the EEPROM and the ID in the ROM.
 
E249 An error occures in the image memory on the image processing PCB CLC5000
E250 KEY matrix is faulty. Related control panel  
E251 A fault in the inverter cooling fan is detected.  
E252    
E253    
E254    
E255    
E256    
E257    
E258    
E259    
E260 The thermistor detects excessive temperature rise of the power supply PCB due to a fault in the power supply unit cooling fan, etc. Related power supply   
E261 Zero-cross signals fail.  
E262 •Power of the printer is not turned ON when the main power of a host machine is turned ON.
•A failure in the power supply fan is detected.
 
E263    
E264    
E265    
E266    
E267    
E268    
E269    
E270 The signal for slide reading and the document leading edge detection signal are delayed or not be generated. Related scanner  
E271    
E272    
E273    
E274    
E275    
E276    
E277    
E278    
E279    
E300 When the main power supply is turned ON after downloading, data of a unrelated model is found in downloaded data.  Related CPU (scanner)  
E301 A failure in the exposure control of the scanning lamp.  
E302 Shading correction failure.  
E303    
E304    
E305 Multipurpose RAM failure. (A fault in RAM for image processing and such.)
Detail code is indicated.
 
E306    
E307    
E308    
E309 Black offset correction failure.  
E310 Editing failure. Related gate array  
E311    
E312    
E313 A fault in the gate array for the motor controller.  
E314    
E315 A fault is detected when encoding the image data.
1. A chip failure is found when writing/reading/verifying the image data by using the register of the encoding chip.
2. An error occurs when encoding the image data.
FAX failure
E316    
E317    
E318    
E319    
E320 A fault is detected in the measurement signal from the CCD. Related CCD  
E321    
E322    
E323    
E324    
E325    
E326    
E327    
E328    
E329    
E330      
E331    
E332    
E333    
E334    
E335    
E336    
E337    
E338    
E339    
E350 •The bar code data for backup and the attached bar code data do not match.
•A fault in the Serial No. PCB is detected when power is turned ON.
Related GZ  
E351 1. The GZ PCB is not connected to the CPU PCB.
2. Versions of ROM for GZ are not consistent.
 
E352 When registering bar code data with Service Mode, a bar code cannot be read. (a parity error, an incorrect bar code, etc.)  
E353 When turning ON the power, inconsistency of the serial number of the RCON (SRAM) and that of the EEPROM is detected.  
E354 •When turning ON the power, inconsistency of the serial No. of the serial number PCB and that of the controller PCB (SRAM)/counter memory is detected.
•When turning ON the power, it is detected that no serial numbers are assigned to the serial number PCB and the controller PCB (SRAM)/ counter memory.
 
E355 When turning ON the power, inconsistency among the serial No. PCB, the controller PCB (SRAM), and the counter memory PCB is detected.  
E356    
E357    
E358    
E359    
E400 An error occurs in the serial communication with DF, ADF, and RDF. Related data line of document feeder  
E401 The pick-up roller does not return to the home position within a specific time.  
E402 Clock pulses of the belt motor are below a specific value.  
E403 Clock pulses of the feeder motor are below a specific value.  
E404 Clock pulses of the delivery motor are below a specific value.  
E405 Clock pulses of the pick-up motor are below a specific value.  
E406 Movement of the guide driven by the side guide motor does not complete within a specific time.  
E407 Movement of the tray driven by the document tray motor does not complete within a specific time.  
E408 Clock pulses from the feeder motor are below a specific value.  
E409 Clock pulses of the CP register motor are below a specific value.  
E410 •The pick-up roller height sensor does not generate signals within a specific time as the pick-up motor is being driven.
•The pick-up roller HP does not send out signals within a specific time as the pick-up motor is being driven.
Related feed of deocument feeder ADF for GP605
E411 The output of the paper sensor is faulty.  
E412 The lock signal is generated at the time when the cooling fan drive signal is generated. DADF-D1
E413    
E414    
E415    
E416    
E417    
E418    
E419    
E420 Backup data cannot be read, or the data is faulty. Related CPU communication of document feeder ADF for GP605
E421 Faults occur when writing backup data, or the written data is faulty. DADF-D1
E422 A transmission error occurs due to faults in IPC of DF/ADF/RDF. (This error code is detected by DF and it is not notified to a copier, so the error code is not indicated.)  
E423    
E424    
E425    
E426    
E427    
E428    
E429    
E430   Related sub feeder  
E431 1. The output of the paper sensor is faulty.
2. The sub pick-up roller does not return to the home position.
3. Clock pulses of the sub feeder motor are below a specific value.
 
E432    
E433    
E434    
E435    
E436    
E437    
E438    
E439    
E440   Related CFF  
E441 CFF motor failure  
E442 CFF exhaust fan failure  
E443 The CFF lamp regulator failure, the CFF lamp failure, a fault in the CFF temperature fuse, or a fault in the CFF controller PCB.  
E444    
E445    
E446 The output of the sensor does not change after the CFF mirror drive signal is generated.  
E447 The CFF leaves the home position, and the power to the Sorter is cut off.  
E448    
E449    
E500 An error occurs in the serial communication with the Sorter or the Finisher, etc. Related data line of sorter/finisher  
E501 An error occurs in the communication within the Finisher controller.  
E502 Coming off of a sensor connector in an optional device is detected:
•The door sensor, paper sort sensor, non-sort sensor, bin outside paper sensor, staple position sensor, etc.
 
E503 An error occurs in the communication between the Finisher controller PCB and the Side Stitcher controller.  
E504 An error occurs in the communication error between the controller PCB and the (height) sensor.  
E505 An error is found in Check SUM for backup RAM when turning the power ON.  
E506 Download fails.  
E507 An error occurs in the communication between the trimmer and the finisher.  
E508    
E509    
E510 Clock pulses are not generated from the feeder motor. Related feed1 of sorter /finisher  
E511 Clock pulses from the feeder motor are below a specific value.  
E512 Clock pulses cannot be detected due to a delivery motor failure, etc.  
E513 Clock pulses cannot be detected due to a tandem feeder motor failure, etc.  
E514 Clock pulses cannot be detected due to a push motor failure, etc.  
E515 Clock pulses cannot be detected due to a tray feeder motor failure, etc.  
E516 Clock pulses from the low speed feed motor are not obtained.  
E517 The home position of the curl removing pressure roller in the buffer path cannot be detected.  
E518 The feeder motor in the paper holder does not reach a specific speed.  
E519    
E520 The stacker unit does not reach the upper limit sensor within a specific time due to a motor failure, etc. Related stacker1  
E521 Input to the tray position sensor is not made within a specific time due to an offset motor failure of the shift (offset) tray.  
E522 The push bar does not return to the home position within a specific time.  
E523 The reference wall does not return to the home position within a specific time.  
E524 The multi guide does not return to the home position within a specific time.  
E525 Automatic adjustment of the bin paper sensor fails, or an error occurs in the automatic adjustment value.  
E526 Automatic adjustment of the bin paper sensor fails, or an error occurs in the automatic adjustment value.  
E527 Automatic adjustment of the stack tray paper sensor 1 fails.  
E528 Automatic adjustment of the stack tray paper sensor 2 fails.  
E529 Automatic adjustment of the tray stacking amount sensor fails.  
E530 The guide plate of the stapler unit does not return to the home position within a specific time. Related stapler  
E531 The stapler does not return to the home position within a specific time.  
E532 The stapler does not return to the home position for the front/rear shift operation within a specific time.  
E533 Automatic adjustment of the paper sensor for the stapler fails, or an error occurs in the automatic adjustment value.  
E534 Bins do not reach the stipulated positions within a specific time while the bin rear end open/close motor is working.  
E535 Clock pulses and such cannot be detected due to faults in the swing unit motor, etc.  
E536 Auto adjustment of the leading edge sensor fails.  
E537 The sheet alignment part does not return to the home position within a specific time while the lower bin guide motor is working.  
E538    
E539    
E540 The home position of the lead cam cannot be detected within a specific time. Related bin shift  
E541 Clock pulses from the shift motor are below a specific value.  
E542 The lead cam of the lower bin unit cannot detect the home position within a specific time.  
E543 Clock pulses of the shift motor for the lower bin unit is out of the specifications.  
E544    
E545 Malfunction of bin flapper 1:
•The sensor cannot detect the operation of the flapper when the flapper solenoid drive signal is generated.
•The sensor detects the operation of the flapper when the flapper solenoid drive signal stops.
Sorter-H1 for CP660
E546 Malfunction of bin flapper 2:
•The sensor cannot detect the operation of the flapper when the flapper solenoid drive signal is generated.
•The sensor detects the operation of the flapper when the flapper solenoid drive signal stops.
Sorter-H1 for CP660
E547    
E548    
E549    
E550 An error in the output from the load system of the power supply unit is detected. Related power supply of sorter/finisher  
E551 A failure in or the stoppage of fans of Sorter/Finisher is detected:
•Power supply fan, punch fan, etc.
 
E552    
E553    
E554    
E555    
E556    
E557    
E558    
E559    
E560 Clock pulses from the upper feeder motor are below a specific value. Related feed2 of sorter/finisher  
E561 Clock pulses from the lower feed motor are below a specific value.  
E562 Automatic adjustment of the folding unit feed path sensor 2 fails.  
E563 Automatic adjustment of the folding unit feed path sensor 3 fails.  
E564 Automatic adjustment of the upper path external bin sensor fails.  
E565 Automatic adjustment of the lower path external path sensor fails.  
E566    
E567    
E568    
E569    
E570 The side gripper motor does not reach the stipulated position within a specific time as it is in operation. Related stack handling unit  
E571 The front gripper motor does not reach the stipulated position within a specific time as it is in operation.  
E572 The side gripper left/right shift motor does not reach the stipulated position within a specific time as it is in operation.  
E573 The front gripper left/right shift motor does not reach the stipulated position within a specific time as it is in operation.  
E574 The front gripper front/rear shift motor does not reach the stipulated position within a specific time as it is in operation.  
E575 The cable wiring unit up/down motor does not reach the stipulated position within a specific time as it is in operation.  
E576 Automatic adjustment of the edge feeding sensor fails.  
E577 The paddle drive motor cannot detect the paddle home position within a specific time as it is in operation.  
E578 •The knurl belt motor does not detect the home position within a specific time as it is in operation.
•The knurl belt motor does not leave the home position within a specific time as it is in operation.
 
E579    
E580 The stack tray motor does not reach the stipulated position within a specific time as it is in operation. Related stacker2  
E581 The stack unit shift motor does not reach the stipulated position within a specific time as it is in operation.  
E582 The tray leading edge stopper motor does not reach the stipulated position within a specific time as it is in operation.  
E583 The sensor is not turned ON within a specific time as the tray auxiliary plate motor is in operation.  
E584 •The shutter sensor is not turned ON within a specific time as the shutter drive motor is in operation.
•It is detected that the shutter detection switch is turned OFF as the tray up-down motor is in operation.
 
E585 The shutter HP sensor is not turned ON within a specific time as the paddle motor is in operation.  
E586    
E587    
E588    
E589    
E590 •The punch motor does not detect the home position within a specific time as the punch motor is in operation.
•The punch motor does not leave the home position within a specific time as the punch motor is in operation.
Related punch unit  
E591 Automatic adjustment of the punch scrap sensor fails.  
E592 Automatic adjustment of the punch trailing edge sensor fails.  
E593 •The puncher cannot detect the home position as the side registration motor is in operation.
•The puncher does not return to the home position as the side registration motor is in operation.
 
E594 •The punch paper end HP sensor does not detect the home position within a specific time as the punch sensor shift motor is in operation.
•The punch paper end sensor does not return to the home position within a specific time as the punch sensor shift motor is in operation.
 
E595 Output of the punch waste delivery sensor does not change within a specific time as the punch waste delivery motor is in operation. Side Finisher-D1
E596    
E597    
E598    
E599    
E5A0 Errors in the trimmer knife motor:
a. The knife motor does not leave the home position within a specific time after the normal rotation drive starts.
b. The knife motor does not return to the home position within a specific time after the normal rotation drive starts.
c. In case of b, the knife motor does not return to the home position after the reverse rotation drive starts.
d. Rotation of the fan motor accompanied by the knife motor is unstable.
Related trimmer  
E5A1 Errors in the trimmer holder motor:
a. When the trimmer holder motor goes down, it does not reach the lower limit home position within a specific time after the holder motor starts to be driven.
b. When the trimmer holder motor goes up, it does not reach the upper limit home position within a specific time after the holder motor starts to be driven.
 
E5A2 Errors in the trimmer pusher motor:
a. When a stack is pushed out, a stack does not reach to the stipulated push-out position within a specific time after the pusher motor starts to be driven.
b. When a stack is moved to the stand-by position, a stack does not reach the stipulated stand-by position within a specific time after the pusher motor starts to be driven.
 
E5A3 Errors in the trimmer trailing edge stopper motor:
a. The trailing edge stopper motor does not reach the home position within a specific time after the motor starts to be driven.
b. The trailing edge stopper motor does not reach the stipulated position within a specific time after the motor starts to be driven.
 
E5A4 Errors in the trimmer press motor:
a. The press motor does not reach the home position within a specific time after the motor starts to be driven.
b. The press motor does not reach the press position within a specific time after the motor starts to be driven.
 
E5A5 An error in the trimmer feed motor:
a. A fixed speed is not obtained within a specific time after the feed motor starts to be driven.
 
E5A6 Errors in the trimmer stopper trailing edge motor:
a. The motor does not reach the stopper functioning position within a specific time after the stopper release motor starts to be driven.
b. The motor does not reach the stopper releasing position within a specific time after the stopper release motor starts to be driven.
 
E5A7 An error occurs in the communication between an trimmer and the CPU of the finisher.  
E5A8    
E5A9    
E5F0 •The paper positioning plate HP sensor is not turned ON within a specific time while the positioning plate motor is being driven.
•The paper positioning plate HP sensor is not turned OFF within a specific time while the positioning plate is being driven.
Related saddle stitcher  
E5F1 The detection pulse of the motor clock sensor for folding is below a specific value.  
E5F2 •The guide HP sensor is not turned ON within a specific time while the guide motor is being driven.
•The guide HP sensor is not turned OFF within a specific time as the guide motor is being driven.
 
E5F3 •The alignment plate HP sensor is not turned ON within a specific time while the alignment motor is being driven.
•The alignment plate HP sensor is not turned OFF within a specific time as the alignment motor is being driven.
 
E5F4 •The stitch operation HP sensor is not turned ON while the stitch motor (rear) is being driven.
•The stitch operation HP sensor is not turned OFF while the stitch motor (rear) is being driven.
 
E5F5 The stitch operation HP sensor is not turned ON within a specific time while the stitch motor (front) is being driven.
The stitch operation HP sensor is not turned OFF within a specific time while the stitch motor (front) is being driven.
 
E5F6 •The paper push plate HP sensor or the paper push plate leading edge position sensor is not turned ON while the paper push plate motor is being driven.
•The paper push plate HP sensor or the paper push plate leading edge position sensor is not turned OFF while the paper push plate motor is being driven.
•The number of detection pulses of the paper push plate motor clock sensor is below a specific value.
 
E5F7    
E5F8 Coming off of a sensor connector in the side stitcher is detected:
•Guide HP sensor, paper push plate HP sensor, paper push plate leading edge position sensor, etc.
 
E5F9 It is detected that a door switch (power supply system) of Saddle Finisher is 'OPEN' while a copier is working.
•Inlet cover, front cover, delivery cover.
 
E600 A failure in RMU extension of an external unit. Related memory unit (digital APC)  
E601 •An error occurs in the communication with an electric sorter.
•An error occurs in the communication with an image server.
•An error occurs in the communication with a hard disk.
 
E602 Hard disk failure.  
E603 Blowout of the fuse on the bus line of the SCSI board.  
E604 Failures in the image memory (including encoding memory):
•When writing/reading/verifying an image memory, a writing failure is detected.
•RAM failure, a failure in mounting the expanded memory.
 
E605 A fault in the battery for image memory.
Although the battery is charged sufficiently and the power is ON within its discharging time, the battery is below a specific voltage.
 
E606    
E607 Input to the clock signal is not made after a specific time passes while the hard disk fan is being driven.  
E608 A fault occurs in the operation controller CPU.  
E609    
E610      
E611    
E612    
E613    
E614    
E615    
E616    
E617    
E618    
E619    
E620 1. An error occurs in the serial communication with the NP editor, etc.
2. All errors occurring in the editor controller PCB are indicated on a host machine.
Related Editer  
E621 An error occurs in the communication between an editor and a copier.  
E622    
E623    
E624 An error occurs in the serial communication between the editor controller PCB and the digitizer PCB.  
E625 An error in RAM on the editor controller PCB.  
E626 An error in the LCD controller circuit on the editor controller PCB  
E627 An error in the gate array on the editor controller PCB.  
E628 An error in the IC for communication on the editor controller PCB.  
E629 An error in the main sequence on the editor controller PCB.  
E630 The projector is not connected. (Blowout of the projector lamp, insufficient light intensity, and a communication failure are included.) Related projector  
E631 A failure in adjustment of light intensity of the projector lamp. (This is detected by a host copier).  
E632 The home position signal for the projector is not input.  
E633 An error occurs in the serial communication with the projector, etc.  
E634 Disconnection of the projector lamp is detected.  
E635    
E636    
E637    
E638    
E639    
E640 •An error occurs in the communication with the IPU.
•An internal error occurs in the IPU.
•The type of an external device cannot be identified.
•An error occurs in the communication with the AHS (PCB for BJ-A1).
Related IPU  
E641 DOS program execution error (upon startup).  
E642 An error occurs in the communication between the image processor PCB and the system unit PCB (upon startup).  
E643 Image memory PCB failure (upon startup).  
E644 Faults related to the interface PCB accommodated to a model (upon startup).  
E645 Faults related to the SCSI interface PCB (upon startup).  
E646 Faults related to the LAN card (upon startup).  
E647    
E648    
E649    
E650 An error occurs in the communication with the film scanner. Related film scanner  
E651 The CCD is not exposed to light even if the mirror solenoid is ON.  
E652 The lens cannot detect the home position due to AF motor failure, etc.  
E653 Signals are not generated from the filter sensor within a specific time.  
E654 Scanner motor failure.  
E655 Auto carrier failure.  
E656 Although the carriage drive motor is being driven, the sensor does not send out signals within a specific time.  
E657 EEPROM backup data is damaged.  
E658    
E659    
E660 A malfunction of IC card. (This is detected by a copier.) Related IC card  
E661    
E662    
E663    
E664    
E665    
E666    
E667    
E668    
E669    
E670 An error occurs in the communication between the multi device controller PCB and a copier. Related multi device controller  
E671 Abnormal temperature rise in the multi device controller unit.  
E672 A failure in the HD (hard disk) in the multi device controller unit.  
E673 A failure in the HD (hard disk) for FAX use in the multi device controller unit.  
E674 FAX PCB failure. Including FAX PCBs other than the multi device controller unit
E675 An error occurs in the initial communication between the IP and the PRCON:
When a system power supply failure occurs, the PRCON is shut down. In this case, interrupt signals keep being sent to the IP, and consequently the IP gets locked up. -> If an error is found in interrupt signals during the initial communication, the error code is indicated.
 
E676 An error occurs in the initial communication between the PRCON and the PS:
When the power supply is instantly shut off, the IP and the PRCON are reset and start rebooting. Meanwhile, the PS is not reset, and is left behind, resulting in no PS board. -> An initial communication failure is detected upon starting up the PRCON, and the error code is indicated if a failure is detected. 
 
E677 An error occurs in the initial communication between an optional controller and an accessory.  
E678 A communication cutout error between an optional roller and an accessory.  
E679 A communication protocol error between an optional controller and an accessory.  
E700 An error occurs in the serial communication. Related data line  Related to the data line between the scanner ass'y and the printer ass'y.
E701 Status parity failure. Related to the data line between the scanner ass'y and the printer ass'y.
E702 Command illegal failure. Related to the data line between the scanner ass'y and the printer ass'y.
E703 Command parity failure. Related to the data line between the scanner ass'y and the printer ass'y.
E704 Status busy failure. Related to the data line between the scanner ass'y and the printer ass'y.
E705 Print request failure. Related to the data line between the scanner ass'y and the printer ass'y.
E706 Print request failure:
•After finishing a copy operation, a copier does not go into the stand-by state.
•After turning the power ON, a copier does not go into the stand-by state.
Related to the data line between the scanner ass'y and the printer ass'y.
E707   Related to the data line between the scanner ass'y and the printer ass'y.
E708   Related to the data line between the scanner ass'y and the printer ass'y.
E709   Related to the data line between the scanner ass'y and the printer ass'y.
E710 An error occurs in the communication IC of a copier upon turning ON the power. Related data line  A copier detects an error in the communication between a copier and an external device. An external device does not have a display function.
E711 An error occurs in the communication IC of a copier after turning ON the power. A copier detects an error in the communication between a copier and an external device. An external device does not have a display function.
E712 An error occurs in the communication IC of the feeder/editor. A copier detects an error in the communication between a copier and an external device. An external device does not have a display function.
E713 An error occurs in the communication IC of the sorter. A copier detects an error in the communication between a copier and an external device. An external device does not have a display function.
E714 An error occurs in the communication IC of the IC card. A copier detects an error in the communication between a copier and an external device. An external device does not have a display function.
E715 An error occurs in the communication IC of the CFF. A copier detects an error in the communication between a copier and an external device. An external device does not have a display function.
E716 An error occurs in the communication IC of the Pedestal. A copier detects an error in the communication between a copier and an external device. An external device does not have a display function.
E717 •An error occurs in the communication IC of ASSIST.
•An error occurs in the communication between a copier and ASSIST.
•ASSIST is dismounted without releasing it using Service Mode (COPIER>OPTION>INT-FACE>B-CLR) after ASSIST is mounted.
A copier detects an error in the communication between a copier and an external device. An external device does not have a display function.
E718 An error occurs in the communication IC of the film projector. A copier detects an error in the communication between a copier and an external device. An external device does not have a display function.
E719 An error occurs in the communication between a coin-operated machine and a host copier. A copier detects an error in the communication between a copier and an external device. An external device does not have a display function.
E730   Related internal controller  
E731 The controller board cannot identify the PDI board. iR3250
E732 An error occurs in the communication between the controller board and the scanner. iR3250
E733 An error occurs in the communication between the controller board and the printer.  
E734 The controller board cannot identify the image processor PCB.  
E735 The controller board cannot access the PCI bus of the image processor PCB.  
E736 An error occurs in the communication between the controller board and the CCU board (FAX).  
E737 When the controller board accesses the SRAM board, read and write operations fail.  
E738 While the controller board is ON, an error is detected when initializing the network interface board.  
E739 An error occurs in the communication (command) between the controller board and the network interface board.  
E740 An error is detected on the LAN card. Related internal controller  
E741 The controller board cannot access the PCI bus of the network interface board, or the PCI bus is found faulty.  
E742 A fault in the RIP1 board is detected as the result of the self-diagnosis.  
E743 An error occurs in the communication between the main controller PCB and the reader controller PCB (detected by the reader)  
E744 The type of the boot ROM and that of the firmware are different.  
E745 An error occures in the token ring board.  
E746    
E747    
E748    
E749    
E750 A ROM designed or a different model is inserted.   iR2100
E751    
E752    
E753    
E754    
E755    
E756    
E757    
E758    
E759    
E800 The auto power off signal of the power supply switch is cut off. Related power supply and fan  
E801 The auto power off signal of the power supply switch is generated. (No indication. This signal is for ASSIST use.)  
E802 Power saving circuit failure (relay failure).  
E803 •The DC low pressure output (5V, 24V, etc.) of the DC power supply (including the composite power supply) is out of the control value.
•The DC low pressure output (5V, 24V, etc.) is not detected.
 
E804 The stoppage of the cooling fan for the power supply unit is detected. If the cooling fan stops, the temperature of the power supply unit might go up, resulting in flaming or smoking.
E805 The stoppage of the exhaust fan is detected, or a failure in rotation of the fan is detected. (GP40 or later machines) The detail code, which can be checked with DISPLAY, was assigned at the end of 1997.
E806 The stoppage of the exhaust fan motor around the ITD (Intermediate Transfer Drum) is detected.  
E807 The stoppage of the exhaust fan motor around the scanner is detected.  
E808 A fault in the fixing drive circuit or the power supply unit is detected.  
E809 The stoppage of the cooling fan of the reader unit power supply is detected.  
E810 The drum cartridge is found not mounted. Related durable  
E811 Photosensitive drum unit memory failure.  
E812 The home position of the ITD (Intermediate Transfer Drum) unit cannot be detected.  
E813 The fixing unit is found not mounted.  
E814 A specific number of copies are made after warning to replace the drum cartridge is indicated.  
E815    
E816    
E817    
E818    
E819    
E820 A fault in the drum intake fan is detected. Related drum/drive-2  
E821 Abnormal temperature rise in the drum cleaner is detected.  
E822 An error is detected in a fan associated with fixing/deliverry.  
E823 A fault in the pre-transfer corona assembly fan is detected.  
E824 A fault in the primary corona assembly fan is detected.  
E825 A fault in the CPU cooling fan is detected.  
E826 A fault in the multi feeder tray fan is detected.  
E827 A fault in the printer's controller power supply cooling fan is detected.  
E828    
E829    
E830 A fault in the separation fan is detected. Related charging  
E831    
E832    
E833    
E834    
E835    
E836    
E837    
E838    
E839    
E900   Related pedestal  
E901 The PLL lock signal is not generated within a specific time after the pedestal motor drive signal is generated.  
E902 A malfunction of the jogging guide plate of the duplexing unit.  
E903 The paper deck lifter does not lift up within a specific time.  
E904 The waste toner box swing cam does not return to the home position within a specific time.  
E905    
E906    
E907    
E908    
E909    
E999 This error code is used only in case codes for self-diagnosis are not determined while a device is under development. It is not used after the mass production of the device is started.    








Sobat havia dapat boleh memanfaatkan translator online jika membutuhkan. Semoga bermanfaat.